45 Articles in this category
What is camera initialisation? When configuring a new IP camera for the first tim...
PTZ Keyboard Setup In this example, we are going to connect to an NVR, with a PTZ...
Open the main menu and select EVENT. 1. Select the channel number then tick the e...
There are 2 settings that need to be applied for motion detection to be recorded....
If you camera is foggy/blurry and you struggle to see anything clearly from the c...
A tour is a selection of live video feeds that get switched between automatically...
Please note, IR settings are only accessible via web interface. Configuring IR S...
Please note: Network cabling needs to be installed by a qualified Licenced Cabler...
There are two different types of recording used on CCTV recorders. Main Stream: F...
Remote Camera Setup Notice! Please read the following information When connecting...
How to check ONVIF version and enable ONVIF 1. Log in to the web interface, Setup...
If you do not wish to see the channel name or time and date, you can remove it fr...
Backlight Compensation (BLC) In scenes where light is shining through into indoor...
In some situations it may be required to have some cameras displayed on a monitor...
Formatting a hard drive means erasing all of the data that is stored on it. This ...
A TP-TL-MR3020 can be used to connect hardwired devices, such as a CCTV Recorder,...
Camera Mounting Requirements Before installing the VSIPNP-2BIRM-I camera, please ...
There are two methods to stream RTMP video to a streaming service: 1) Use a PC or...
In the video above, Jeff demonstrates how by all cameras are viewable by default ...
Camera Snapshot There are two types of Snapshots, Event or Schedule/Time Based E...
If you have purchased a recorder without a hard drive, or wish to install an addi...
How To Enable Alarm Box To CVR's From PIR Motion Cameras Connect the PIR camera t...
When installing a third party camera to a VIP or Watchguard NVR, the NVR will not...
Setting the idle motion will prevent the camera to stop your IVS preset settings ...
Alarm Inputs and Outputs have a wide range of uses, from integrating your alarm p...
How To Disable Audio on CVR From OSD Menu Step 1: Right click on the camera you ...
To enable ActiveX controls go to: Tools > Internet Options > Security > ...
Fisheye Dewarping Modes To access the dewarping menu, right click the camera chan...
In the video above, Jeff demonstrates how important it is to keep water out of yo...
G.726 Audio @ 8000khz and noise filter enabled. Removes warbled audio...
Please see this guide If you wish to hide cameras when no user is logged in Follo...
Recorders with 1 VGA and 1 HDMI do not have this option. Only if your recorder ha...
RTSP - Real Time Streaming Protocol The RTSP link is used to integrate a camera o...
If the camera you are using has a microphone or microphone input, follow the belo...
Camera Overlay Display Options In the Main Menu, select Camera. In Camera > Ov...
Follow the steps below to configure your recorder for Remote Access. Warning Have...
In this example, we will be wiring a SPKR-TAV to a recorder. When a camera trigge...
What is Corridor Mode? Corridor mode, also know as 9:16 mode, is a feature on mos...
Select device manage and select the device you wish to edit the extra stream type...
Below is how to setup your IP camera to take snapshots at specified times. In thi...
1. Go to MAIN MENU, select NETWORK under setting, then EMAIL. 2. Click Enable at ...
This is how to wire the devices required. The Station and the Access Point need t...
Standalone Camera over a pair of WT5-ULBs This guide will show you how to initia...
SNMP MIBs (Management Information Base) describe OIDs (Object Identifiers) for SN...
24/7 Colour low light footage at 0.001lx Sample footage compared to 2mp turret - ...